Home CodeArduino Due ADXL337 accelerometer and Arduino Due example

ADXL337 accelerometer and Arduino Due example

by shedboy71

In this article we connect an ADXL337 accelerometer to an Arduino Due

The ADXL337 is a small, thin, low power, complete 3-axis accelerometer with signal conditioned voltage outputs. The product measures acceleration with a minimum full-scale range of ±3g. It can measure the static acceleration of gravity in tiltsensing applications, as well as dynamic acceleration resulting from motion, shock, or vibration.

The user selects the bandwidth of the accelerometer using the CX, CY, and CZ capacitors at the XOUT, YOUT, and ZOUTpins. Bandwidths can be selected to suit the application, with a range of 0.5 Hz to 1600 Hz for X and Y axes, and a range of 0.5 Hz to 550 Hz for the Z axis.

 

Parts List

Name Link
Arduino Due Black Due R3 Board DUE-CH340 ATSAM3X8E ARM Main Control Board with 50cm USB Cable CH340G for arduino
ADXL337 3-axis ADXL337 GY-61 Replacement ADXL335 Module Analog Output Accelerometer
Connecting wire Free shipping Dupont line 120pcs 20cm male to male + male to female and female to female jumper wire

Schematic

 

arduino due and adxl337

arduino due and adxl337

 

Code

No libraries required – this is a sparkfun example

[codesyntax lang=”cpp”]

// Make sure these two variables are correct for your setup
int scale = 3; // 3 (±3g) for ADXL337, 200 (±200g) for ADXL377


void setup()
{
  // Initialize serial communication at 115200 baud
  Serial.begin(115200);
}

// Read, scale, and print accelerometer data
void loop()
{
  // Get raw accelerometer data for each axis
  int rawX = analogRead(A0);
  int rawY = analogRead(A1);
  int rawZ = analogRead(A2);
  
  // Scale accelerometer ADC readings into common units
  // Scale map depends on if using a 5V or 3.3V microcontroller
  float scaledX, scaledY, scaledZ; // Scaled values for each axis
  scaledX = mapf(rawX, 0, 675, -scale, scale); // 3.3/5 * 1023 =~ 675
  scaledY = mapf(rawY, 0, 675, -scale, scale);
  scaledZ = mapf(rawZ, 0, 675, -scale, scale);

  // Print out raw X,Y,Z accelerometer readings
  Serial.print("X: "); Serial.println(rawX);
  Serial.print("Y: "); Serial.println(rawY);
  Serial.print("Z: "); Serial.println(rawZ);
  Serial.println();
  
  // Print out scaled X,Y,Z accelerometer readings
  Serial.print("X: "); Serial.print(scaledX); Serial.println(" g");
  Serial.print("Y: "); Serial.print(scaledY); Serial.println(" g");
  Serial.print("Z: "); Serial.print(scaledZ); Serial.println(" g");
  Serial.println();
  
  delay(2000); // Minimum delay of 2 milliseconds between sensor reads (500 Hz)
}

// Same functionality as Arduino's standard map function, except using floats
float mapf(float x, float in_min, float in_max, float out_min, float out_max)
{
  return (x - in_min) * (out_max - out_min) / (in_max - in_min) + out_min;
}

[/codesyntax]

 

Output

Open the serial monitor and you will see something like this

X: 612
Y: 500
Z: 554

X: 2.44 g
Y: 1.44 g
Z: 1.92 g

X: 619
Y: 478
Z: 510

X: 2.50 g
Y: 1.25 g
Z: 1.53 g

 

Links

https://www.analog.com/media/en/technical-documentation/data-sheets/ADXL337.pdf

Share

You may also like